Cattle Stunning and the Bleed Rail: Sizing the First Two Minutes

How takt time and bleed duration set the number of bleed positions, rail length and hoist count on a cattle line at 20, 40 and 60 head per hour.

Cattle lines rarely lose rate at the splitting saw. They lose it in the first two minutes, between the restraint box and the end of the bleed rail. A carcass that is still bleeding when it reaches the dressing rail blocks every station behind it, and a bleed rail measured from a photograph instead of from the takt time does exactly that.

Planning basis, 13 November 2026. Live weight 450–650 kg, carcass 250–380 kg, one 8-hour shift, halal and conventional routes kept apart because their first two minutes differ. The figures are for layout and budget discussion, not a quotation.

Bleed positions come from a division, not from a preference

Fix the takt first. 20 head/h is one animal every 180 seconds, 40 is 90 seconds, 60 is 60 seconds. Divide the bleed duration by the takt and round up; that is how many positions the rail needs. Cattle bleed for 90–120 seconds: a chest stick empties the carcass at the short end, a halal neck cut sits at the long end because the vessels are severed without opening the chest.

At 20 head/h, 120 seconds of bleeding fits inside a 180-second takt and one position is enough. At 40 head/h, 120 over 90 is 1.33, so two positions. At 60 head/h it is exactly two, with nothing to spare. That single integer sets rail length, hoist count and how many people stand at the rail — and it is the number most often missing from a specification.

First two minutes by nominal rate (basis as stated above)
Item20 head/h40 head/h60 head/h
Takt180 s90 s60 s
Bleed duration to plan with90–120 s90–120 s90–120 s
Bleed positions122
Carcasses on the rail at once122–3
Bleed rail, installed length8–10 m10–12 m12–15 m
Restraint box cycle, upper limit150 s85 s55 s
Hoist rating per unit1,000 kg1,000 kg1,000 kg
People on the first two minutes234

Two rails, and the transfer between them

Bleeding happens on a lower rail so the operator reaches the neck without a platform. Dressing happens on a higher rail so the hide puller and the splitting saw have clearance. For cattle that means roughly 2.8–3.2 m to the top of the bleed rail and 3.8–4.4 m to the top of the dressing rail, checked against the clear height of the building rather than assumed from it.

The transfer is one hoist lift of 0.8–1.2 m and it is where many lines quietly stall. A fixed-speed hoist at 0.3 m/s adds 3–4 seconds per head. On a 60-second takt that is 5–7% of the cycle spent lifting, which is invisible on a layout drawing and very visible on the floor at the end of a shift.

At 60 head/h the restraint box is the limit

A rotary or wedge box needs 45–75 seconds to take an animal, restrain it, allow the stun and release the carcass. With a 60-second takt the box has to run at the bottom of that range every single cycle, and one animal that refuses to enter costs the line more than any downstream machine can recover. This is why 60 head/h layouts usually carry two boxes, or one box fed by a race that holds two animals, while 20 and 40 head/h run a single box with slack.

Halal and conventional split in the same two minutes

Conventional: stun, hoist, chest stick, 90 seconds of bleed. Halal: no stun or a reversible head-only stun, the animal hoisted and positioned for the neck cut, then 120 seconds of bleed. The rail length is the same in both cases — the difference is time, not hardware — but the halal route needs the animal held in a defined orientation at the cut, which changes the restrainer and the hoist height. Ask a supplier which of the two routes the quoted rail was drawn for. One rail described for both is a warning sign, not a saving.

What goes wrong after commissioning

  • Rail sized from a similar plant. Installed length has to follow takt × bleed time plus entry and transfer clearance; copying a neighbour’s 10 m rail into a 60 head/h line leaves two carcasses short of space.
  • Transfer time left out of the takt. The hoist lift and the rail switch are part of the cycle at every rate, and they dominate above 40 head/h.
  • One hoist serving two rails. It becomes the bottleneck the first time a carcass needs a second lift.
  • Bleed rail built to the minimum. Two metres saved at the rail are paid back every shift in carcasses entering dressing before they have finished bleeding.
  • Blood collection added later. If blood is a product rather than waste, the collection point sits under the bleed positions and needs floor fall and a drain run decided before the slab is poured.

Three answers place a cattle project in one row of the table above before any drawing exists: head per shift, live weight range, and whether the route is halal or conventional. Add the building’s clear height and the rail heights follow. The cost and quotation guide shows what sits outside the machine scope, and the layout page lists the measurements the building has to supply.

What to send with an enquiry

  • Rate and shift: head per shift and hours available, so the takt can be fixed before equipment is chosen.
  • Weight range: live weight at intake, because it sets the hoist rating and the rail pitch.
  • Route: halal or conventional, and for halal whether any stun is used at all.
  • Building: clear height under the beam and the floor area available for the bleed and dressing zone.

Use the project brief form for the four items above, or compare the two routes on the halal cattle abattoir and conventional cattle abattoir pages. Equipment detail sits on the restraint box, cattle hoist and bleeding conveyor pages.